Search:

I had mine done through Dallas Steering Wheel and am very happy qith the work.
http://www.dallassteeringwheel.com/

Thanks the info guys. I am going to put in an order for the OEM mounts. Unfortunately I had cut the nub off one mount before taking the other out of the box and seeing the difference.

I will post...

Does anyone have a stock M3 mount handy that they could measure the height for comparison?

Only one has a part #, the other has no markings at all. Both came with the correct part #'s listed on the Corteco boxes that they came in.

In terms of age, I have no idea. Both were received at...

You are correct, the 740iL mounts should lower the engine by about 1/4".

The pictures above are a comparison of two 740iL mounts, I believe the left and right side mounts should be the same...

I am getting ready to install some 740iL mounts that I recently picked up.

p/n 11 81 1 094 149 (left)
p/n 11 81 1 094 150 (right)

As I was getting ready, I noticed that the two mounts I have...

At this point I am going to hold onto it. By the time shipping into the US is added I'm not sure there would be much value.

I'm going to wait for progress on the group buy.

Sorry, was slow to get back.

To confirm it is part# 51711933125

Still available. I just recieved some in my order that I recently placed. I can post part# when I get home (currently on my phone).

I found the part number in xworks thread. He laid out all the...

I had a brain fart when I originally ordered my trunk mat. I was going with the flow...forgetting that my trunk is smaller than most due to the aux fuel tank. Any chance to having a trunk mat made...

My understanding is that idle is controlled by the ECU, and that the Maxx setup should not influence base idle speeds. The idle screw does not change the idle because Maxx adjusts fuel based on air...

Just completed a transaction with Alpaneras, he was always very quick to communicate and very open/honest about the product he was selling. I received the products in the described condition with...

I have success using a ratcheting wrench and a non ratcheting wrench on the other side. Its a very slow going process as I only get a couple degrees of movement on the ratcheting wrench. I put it...

Here is a link to the O.Z version which is more highly sought after.

O.Z Version

I'm really liking the beefy tires on the RS's. Its a nice change from 17's with small sidewall, or stretched tires.

Looks well sorted, good luck with the 02 hunt.

:clap:

Morris, how has your fuel rail been holding up?

Very nice work.
I downloaded your shim size calculator quite a while back. Its a great tool that eliminates all the guess work!

Thank you for taking on this project.

Is that yours Lee?

It looks like very nice product from the website.

Pm Sent

I have purchased a couple of their pad heaters for vehicles that I drove while living in a colder climate. Installation was really easy, scuff the oil pan, make sure pan is clean, stick the pad on...

Where are the splash guards from? I've never seen anything like that on the M3.

This man speaks the truth! Definitely get new lock washers. I installed my lock washer with an oversized socked and hammer. I used the socked to press the lock washer around the nut, it worked quite...

Yes, the dots should be lined up.

Hi Group,

I am looking for some brake duct backing plates in good condition.

If you have something please email me paelick @ gmail . com

Thanks,
-Peter

Not my cup of tea, but to each their own. If I saw the car on the street I would walk up and ask to take a look. Even if it isn't to my styling I can respect others modifying their cars to their...

I'm not positive, but 61131350848 looks like it might be right?

That was the link I was going to post--I was browsing from my phone earlier and don't like fooling around with posts from the phone.

I am trying to build up the courage to try replacing bearings...

I am in London, but my car hibernates in the Kawartha's during the winter months.

I used the harbor freight tool as well. It worked very well for me, but as mentioned it is important to pay attention to the threads on the screw. I was constantly making sure they were lubed to...

I hope I don't muddy the waters, but here is a recent analysis I had done. The most recent report is from using Mobile 1 15w50....

I copied the same setup last summer, it has worked out very well for me.

For the aluminum, I ordered it from onlinemetals.com. I ordered 6061-t6 extruded aluminum (5"OD x 0.125" Wall x 4.75" OD),...

I'll throw my recommendation in for Luis and the IIgo chip. I bought one last year to use with my Maxx A/N setup, it allows me to make some minor timing adjustments with the FQS switch. Outside of...

That is my understanding. There was a thread on a Miata forum where a TireRack rep was suggesting that these are replacements for the Z1 Star Specs.

I currently have Z1 SS and have been very...

Welcome!

I look forward to seeing what you do with the car.