Search:

That is how they should be - all mine have been.

And just found this on ebay Germany

Do not know for sure but an E36 one might do it.

BMWFANS E36 M3 Gearshift emblems

Don't laugh - it's had a hard life!

The holes that the spring mounts in should have a rubber grommet at both ends - this determines that it is the small holes and you are right the longer end goes...

Take the bracket off the block. Attach the engine mount to the bracket (almost tight). Drop it into the cross-member then bolt the bracket back up to the block.

Oh, I guess you probably have to...

Your wire #1 (Bk, Gn/Bk, Bk/Br) with three pin connector is for dual temp switch on thermostat for auxiliary fan.

Blue with pink (could it be violet) and brown = Washer fluid level switch.

Probably find that the dust seals may have gone, allowing rust to start down towards the fluid seal. I would say that it would be worth rebuilding including sand blasting and repainting.

The 535...

Koala has a procedure for adjusting CO on the AFM which, if I understand it correctly, basically seems to be setting the CO with the O2 sensor disconnected to the same value that is recorded with the...

This happened to me last year.

Fortunately I had the column trim off at the time.

It was the steering lock part of the mechanism that was jamming.

I was able to use a chisel on the shear...

Solder (I think).

Not sure what the process does for changing fluid in ABS that otherwise would not happen - but Koala is usually good info.

Koala also says that you should....... "Find a piece of vacuum hose [I...

If you are lucky and the head of the bolt is still hex and the nut remains welded to the bracket............

You can go over the top of the exhaust with a socket and about 20" of extensions. Get...

Am I right in thinking that bolt screws into the timing chain case? If that is the one, make sure that the bolt you use is not too long. If the bolt bottoms out in the threaded hole and you keep on...

Loads of flex agent - the temperature expansion and flex on the rear wing is significant. I have known even well respected bodyshops have trouble stopping repaints from cracking.

Have you thought...

In the UK that stuff is (traditionally) called "shoddy" and it is made from recycled clothing and other material. Having googled it, it seems fairly hard to find in small quantities. As Leigh...

Now I know why I am getting loads of emails on this all of a sudden. Somebody posted a reply and brought it back to the top of the list.

Of course it sold - don't they all if they represent...

Part of the plenum. You will need to get one made.

Anybody know what it does??

Quick check reveals that the ABS pump and relays look like pretty standard part numbers across E30s. Probably OK to swap the relays over.

I hope it is not too cold and snowy!!

When trying to slide open, if you push and hold the button and then use the palm of your hand to push or tap (light thump?) the outside rear of the panel does that start it on its way? Sounds to me...

Yes, You really need new lock washers, and whatever else you do, do not forget to put the bearing retaining circlips back on before you put the hub back on!!

Leigh

235/40x17 are 1.8% or 11mm bigger in diameter than standard 16s and are mighty tight on the front on 8" ET20 rims. 225/40x18 are 28mm bigger and are sure to be a problem with clearance...

Not sure if this is a help, or not.

If you remove the carpets I think there is a hole above the location of the rear control arm mount.

You may be able to access through there to put in a...

No, for sure, they have the levers to tip them forward mounted lower down on the side of the backrest, with different handles on the door side (shorter) They also have rearward travel restricters on...

Is cost a consideration? Do you know the cost of the 2.5 crank?

Not that one, unfortunately. More like a right angled Junior Timer connector. I can't find them anywhere. Perhaps you will have to find someone scrapping a 4 door with electric windows. Then you can...

It would appear that there is still availability on pre-made seat base and seat back cloth kits (like the photo) in antharazit 0304 and 0379 they may give you the bolster cloth you are looking for...

The 0211 code is for the interior ie houndstooth with plain.

The part number is for a seat base re-upholstery kit (ie all the cloth parts made up in to two bolsters and the seat and thigh...

If you think this looks right the upholstery code is 0211. I think you might find it hard to get the genuine stuff.

West Trading BV do lots of cloth but I can't see this one
...

That looks like the Koala manual, and it is just the way to do it.

+1 for Carbtune

If he is not sure now he never will be. He has been going at this for three months and his last video is pretty well conclusive that it is all out of time.

With respect, I do not think it would...

Decent shop that knows S14s, perhaps a couple of hours labour to time the cams.

Then they could tell you what else was wrong. If you still have no compression due to bent valves, then at the very...

Looks as though it may be just part number 21 after all.

Really hard to find a photo of this area but eventually found this one courtesy of Leigh (bigbird76) - Hope you do not mind me borrowing it...

The bit that is part of the bodyshell that sits in the top half of the donut? Then take a look at #15??? which is 41 12 1 911 152 or #17 ?????

BMW Fans